DIY Iontophoresis

I have seen many positive reviews on DIY iontophoresis device recently. Here I have listed out materials that you need to build a device. Note that I am not responsible for any accidents, please use rubber gloves if necessary.

  1. 2 x 9 volt batteries
  2. Alligator clips
  3. Sponges
  4. Aluminium pans
  5. Vaseline (optional)
  6. Pool noodles (optional)

How to build the device

Step 1 – Put the sponges into the aluminium pans and pour tap water into it. The amount of water must be enough to cover your palms or feet.

Step 2 – (Optional) Cut and put your pool noodles to cover the edges of the pans. This is to prevent electrical shock if you accidentally touch the aluminium plans.

Step 3 – Connect the batteries together. Connect the batteries and pans with alligator clips.

This is how your iontophoresis device suppose to look like.

Treatment process

Step 1: Put a dry towel or rubber mat under your pans to prevent any accidental electrical shock.

Step 2: Make sure both aluminium plans do not touch each another.

Step 3: If you have cut on your skin, please apply generous amount of vaseline on it first.

Step 4: Put one palm/foot into the pans followed by the other. DO NOT PUT both palms or feet into the pans at the same time (electrical shock)

Step 5: Treat your palms/feet for 10 – 15 mins.

Step 6: Remove your palms/feet from pans.

Step 7: Switch the polarity by changing the alligator clips on the pans. For example, red clip is connected to Pan 1 and black clip is connected to Pan 2 at the beginning of the treatment, Now just connect red clip to Pan 2 , black clip to Pan 1.

Step 8: Treat your palms/feet for 10-15 mins , then you are done.

FINAL Step: Remove the batteries and alligator clips. Leaving it connected after your treatment may cause fire.

Do it once or twice a day for 1-4 weeks, depending on individual. Once dry, you can maintain the treatment once a week. Please stop if you are feeling uncomfortable or too painful.

[BM language or Versi BM]

Baru-baru ini, ada banyak review on DIY iontophoresis machine. Bahan-bahan untuk membuat machine ini senang aje, semua bahan boleh dibeli di kedai hardware ataupun kedai DIY. I tidak akan bertanggungjawab atas sebarang kemalangan, gunalah sarung tangan getah kalau perlu.

  1. 2 biji 9 volt batteri
  2. Klip Alligator
  3. Sponges
  4. Aluminium pans (untuk baking)
  5. Vaseline (optional)
  6. Pool noodles (optional)

How to build the device

Step 1 – Letak sponges di dalam aluminium pans and tuang air paip ke dalam. Tinggi air mesti cukup untuk menutup tangan atau kaki.

Step 2 – (jika perlu saja) Potong and lekat pool noodles untuk menutupi sisi pans. Ini untuk mencegah litar pintas kalau kulit kita menyentuh aluminium pans nanti.

Step 3 – Sambung batteri. And sambung allligator clips dari bateri ke pans.

Contohnya,

Cara Рcara treatment 

Step 1: Letak tuala kering di bawah aluminium pans anda. Pastinya tempat untuk treatment kering.

Step 2: Pastinya kedua-dua pans tak sentuh or litar pintas akan berlaku.

Step 3: Kalau permukaan kulit di tangan or kaki tercedera, cuba sapu vaseline dulu.

Step 4: Letak satu tangan/kaki dulu ke dalam pan dan diikuti oleh tangan/kaki yang lain. JANGAN LETAK KEDUA-DUA tangan (atau kaki) pada masa yang sama. Litar pintas akan berlaku.

Step 5: Treat tangan/kaki untuk 10-15 mins.

Step 6: Keluarkan tangan/kaki, one by one.

Step 7: Tukar polarity dengan menukar klip alligators di pans. Klip hitam tukar tempat dengan klip merah.

Step 8: Treat tangan/kaki untuk 10-15 mins , dan treatment dah selesai.

Anda boleh buat treatment satu or dua kali sehari (pagi and malam). Treatment kena continue untuk 1-4 weeks, bergantung kepada individual. Bila dah kering, anda boleh kurangkan treatment kepada satu kali seminggu.

 

Leave a Reply

Your email address will not be published. Required fields are marked *